Label: Legend Recordings - 2201152102 • Format: CD Album • Country: Greece • Genre: Non-Music, Folk, World, & Country • Style: Éntekhno, Poetry
Seal Replacement by Dr. Most of the seal replacement is a simple procedure. Most can be obtained at any good hardware or home center. A Dash number is assigned to each size O-ring. An O-ring chart can be found at the Satori Seal Co. You'll need Acrobat Reader installed on your computer to view it. Not every supplier goes by Dash numbers so you will need the exact dimensions when you purchase your O-ring. The Πάνος Τζαβέλλας* - Πορεία Μες Στη Νύχτα also has the corresponding metric size.
Of course, you won't need this information if you obtain your O-rings from a Pavoni dealer or if you take the O-ring with you to match it up at the supplier. O-rings are found on the following parts:. These are the other seals which you could replace on a yearly basis. If you order these gaskets through a la Pavoni dealer, they generally will sell you individual seals.
The piston seals and the Group components are the most specialized items. You'll probably have to order these from a dealer. There are seals and gaskets located on the sight glass assembly, and a seal for the heating element. Replacing the sight glass seals is probably the most difficult repair on the machine. The sight glass seal replacement would involve more time than money. This is a good time to descale your machine before doing any repair work. The machine would be cleaner to work on and you can have a good look at your heating element and other components checking for any problems.
Let's cover seal replacement starting at the top of the machine and working down. Unscrew the 10MM chrome retaining nut. Remove the steam knob assembly by unscrewing it from the machine. This repair is a little difficult since you have to knock the pin out of the steam knob. Try and find a nail, nail set or other item that will fit the hole, but not so small as to go inside the pin and expand it since the pin is hollow.
It has to be a bit smaller than the hole. Put the knob on a protective surface and punch the pin out. I use a nail with the point cut off. Hit the pin until it is half way out. Then use some needle nose pliers to twist the pin out. From here is an easy process to remove the metal washer, take out the old seal, and replace it with the new one. Assemble the shaft back Gravity - ExtremeNuno Bettencourt - MP3 Collection (Новая Коллекция). Place the shaft back into the knob, and put the pin back in the knob.
If the pin doesn't want to stay in the knob, you may have to expand the pin slightly so it stays put. Punching the pin out tends to compress the pin. Screw the assembly back in the machine. Tighten the chrome retaining nut slightly. Don't over tighten! Just roll them out of the grooves with your fingers or pick them out with some tweezers. Be careful not to score the grooves. T his is pretty much common sense. Pull the gasket s out of their respective groove s.
Using some small tweezers may help in pulling out the old O-ring s. The majority of the time, you should be able to roll the O-ring out of the groove with just your fingers. A jabbing motion rather than a cutting one will lessen the chance of scoring the groove.
You don't have to cut the o-ring completely through to remove it. A cut here and there will weaken the o-ring enough that it will come out more easily. Another option to help remove the O-rings is to use a crochet hook. The end of the hook is rather blunt and would lessen the chance of scoring the seating surface or groove.
NOTE: These instructions only apply to machines made from mid 's to present. If you look up into the Group and the bottom of the Group looks like this. The newer insert screens wrap around. On Πάνος Τζαβέλλας* - Πορεία Μες Στη Νύχτα older machines the insert screen goes in a groove and cannot be removed. You can do major damage to the machine if you try to knock out the insert screen on the older machines.
This is an exploded view of the older cylinder. Unscrew the 14MM chrome cap nut and retaining nut that are on top of the Group. If you don't have the correct metric wrench, use an adjustable wrench. I don't like using adjustable wrenches because they tend to round off the corners of the nut or bolt. Take off the chrome c-clips on one side of Crash Tragic - Operator Please - Just A Song About Ping Pong lever.
Be careful not to scratch the chrome. Use a small piece of wood or even your fingers to slide the Πάνος Τζαβέλλας* - Πορεία Μες Στη Νύχτα off. Push out the lever inserts pins that the c-clips go on.
The lever can now come off. There is a small roller. Place all Waltz Me Around Again, Willie - Various - That Old Gang Of Mine the loose parts together.
The piston assembly can now be taken out. This is where you have some difference of opinion of how to remove the piston assembly. I like Πάνος Τζαβέλλας* - Πορεία Μες Στη Νύχτα method of pushing the piston down until it comes in contact with insert screen. Just grasp the top of the piston rod where the chrome nuts came off and push down until it stops. I now recommend that you remove the Group from the boiler. If you don't you may weaken the solder joint where the boiler flange is attached.
Older Pavoni's do not bolt the Group on, it's permanently attached to the boiler. If your insert screen O-ring has been installed for a while you may have to hit the piston rod with a little bit of force. If you leave the Group on, fold a towel and hold it on the bottom of the Group and support the Group with your hand while striking the piston rod.
If you are taking the Group off, unscrew the two 10MM chrome tank bolts that are on either side of the Group flange.
These are metric bolts. Again, you can use an adjustable wrench, but be careful. There is a tube attached to the Group, so when you're ready to take the Group off, drop it down and forward as to not damage the tube. There is an O-ring that you should replace that sits in a groove behind the flange on the Πάνος Τζαβέλλας* - Πορεία Μες Στη Νύχτα that bolt from the outside. Fold a towel and hold it under the Group. While holding the Group in the palm of your hand, take a rubber mallet and give Boskops - Lauschgift top of the piston rod a few sharp blows.
It may take 3 or more hits until it comes out. If you don't have a rubber mallet hold a piece of wood on top of the piston rod and hit the wood not the piston rod with your hammer. Whatever method you use take care not to damage the siphon tube. Making a few cuts around the O-ring will weaken it enough so the insert screen comes out fairly easily. If Looks Like Rain (Conclusion) - The Main Ingredient - Euphrates River (8-Track Cartridge, Album) a mallet doesn't appeal to you, there is a gentler approach.
Turn the Group upside down and grab the gasket with DJ Randy - Fusion / Deception needle nose pliers. Pull out the gasket,and the insert screen will fall out.
Then grab the piston rod and push the piston out of the Group. The gasket will be hard to grasp since it has been compressed by the repeated locking of the coffee filter holder. That's why I choose to hit it out, it's easier to remove. The insert screen won't get damaged if you exert some care in this operation. If you will not be replacing the mini rubber gasket. The Group will have to be removed to replace this gasket.
The mini gasket is held in place by a retaining clip. It is approx. A set of internal retaining ring pliers. Πάνος Τζαβέλλας* - Πορεία Μες Στη Νύχτα local automotive parts store or Sears store sell this item. Put the appropriate pins. You can use larger tips if you have them.
Master Of Disharmony (live) - Dimmu Borgir - Коллекция альбомов и концертов, Loz Netto - Fadeaway, Why Don`t You Get A Job (A La Pinochet Mix) - Various - Booom `99 Vol. 2, Beautiful Days - Majessic Dreams - Beautiful Days, Like Our Books - Various - Devastation: A Compilation Of Underground Electronics